Gästesite » wholesalenfljerseyscheapstore.com

Question: 1

What is the maximum number of switches that can be stacked using Cisco StackWise?


A. 4
B. 5
C. 8
D. 9
E. 10
F. 13


Answer: D


Question: 2


A network engineer wants to add a new switch to an existing switch stack. Which configuration must be added to the new switch before it can be added to the switch stack?


A. No configuration must be added.
B. stack ID
C. IP address
D. VLAN information
E. VTP information


Answer: A


Question: 3


What percentage of bandwidth is reduced when a stack cable is broken?


A. 0
B. 25
C. 50
D. 75
E. 100


Answer: C


Question: 4


Which set of configurations will result in all ports on both switches successfully bundling into an EtherChannel?


A. switch1
channel-group 1 mode active
switch2
channel-group 1 mode auto
B. switch1
channel-group 1 mode desirable
switch2
channel-group 1 mode passive
C. switch1
channel-group 1 mode on
switch2
channel-group 1 mode auto
D. switch1
channel-group 1 mode desirable
switch2
channel-group 1 mode auto


Answer: D


Question: 5


How can the traffic that is mirrored out the GigabitEthernet048 port be limited to only traffic that is received or transmitted in VLAN 10 on the GigabitEthernet01 port?


A. Change the configuration for GigabitEthernet048 so that it is a member of VLAN 10.
B. Add an access list to GigabitEthernet048 to filter out traffic that is not in VLAN 10.
C. Apply the monitor session filter globally to allow only traffic from VLAN 10.
D. Change the monitor session source to VLAN 10 instead of the physical interface.


Answer: C


Question: 6


A network engineer wants to analyze all incoming and outgoing packets for an interface that is connected to an access switch. Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch? (Choose three.)


A. A monitor session on the distribution switch with a physical interface as the source and the remote SPAN VLAN as the destination
B. A remote SPAN VLAN on the distribution and access layer switch
C. A monitor session on the access switch with a physical interface source and the remote SPAN VLAN as the destination
D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and physical interface as the destination
E. A monitor session on the access switch with a remote SPAN VLAN source and the physical interface as the destination
F. A monitor session on the distribution switch with a physical interface as the source and a physical interface as the destination


Answer: B Dan Feeney Hat , C, D


Question: 7


After an EtherChannel is configured between two Cisco switches Mike Williams Hat , interface port channel 1 is in the downdown state. Switch A is configured with channel-group 1 mode active, while Switch B is configured with channel-group 1 mode desirable. Why is the EtherChannel bundle not working?


A. The switches are using mismatched EtherChannel negotiation modes.
B. The switch ports are not configured in trunking mode.
C. LACP priority must be configured on both switches.
D. The channel group identifier must be different for Switch A and Switch B.


Answer: A


Question: 8


An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server. What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?


A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.
B. Adjust the EtherChannel load-balancing method based on destination IP addresses.
C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.
D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.
E. Adjust the EtherChannel load-balancing method based on source IP addresses.


Answer: E


Question: 9


Interface FastEthernet01 is configured as a trunk interface that allows all VLANs. This command is configured globally:
monitor session 2 filter vlan 1 - 8 Kyzir White Hat , 39, 52
What is the result of the implemented command?


A. All VLAN traffic is sent to the SPAN destination interface.
B. Traffic from VLAN 4 is not sent to the SPAN destination interface.
C. Filtering a trunked SPAN port effectively disables SPAN operations for all VLANs.
D. The trunk's native VLAN must be changed to something other than VLAN 1.
E. Traffic from VLANs 1 to 8 Derwin James Hat , 39, and 52 is replicated to the SPAN destination port.


Answer: E


Question: 10


A network engineer notices inconsistent Cisco Discovery Protocol neighbors according to the diagram that is provided. The engineer notices only a single neighbor that uses Cisco Discovery Protocol Jahleel Addae Hat , but it has several routing neighbor relationships. What would cause the output to show only the single neighbor?


A. The routers are connected via a Layer 2 switch.
B. IP routing is disabled on neighboring devices.
C. Cisco Express Forwarding is enabled locally.
D. Cisco Discovery Protocol advertisements are inconsistent between the local and remote devices.